Steel that works for a living

Workshop Benches & Steel Storage

Actionchoiceflow builds and supplies heavy workshop benches, steel shelving and mobile storage for Australian garages and trade workshops. Everything on this page is rated to take the load it says it will, and we list the exact steel thickness so there is no guesswork before you order.

Made in Australia

Three workspaces, one wall

Run a welding bench, a clean assembly bench and bolt storage along a single run without giving up floor space.

600 kg Static load on a 2.4m bench
2mm steel tops Adjustable feet Lockable castors Powder-coated frames Galvanised shelving
Why workshops order from us

Storage and benches built to take a hit

We fabricate in Brisbane and deliver assembled wherever access allows. No flat-pack that wobbles the first time you lean on it.

Steel workbench with a vice bolted to the top
Benches

2.4m fabrication bench with steel top

A 2mm steel working surface welded to a 50mm box frame. Rated to 600kg static and drilled for a standard vice and grinder mount.

Bolted steel shelving unit loaded with storage bins
Shelving

Modular steel shelving run

Starts at 900mm and extends in 900mm bays. Each shelf holds 350kg evenly spread and the uprights bolt to the floor if you need them fixed.

Rolling tool cabinet with drawers open
Mobile storage

Lockable rolling tool cabinet

Seven drawers on ball-bearing slides, a 6mm steel top and four 125mm castors, two of them braked, so it stays put under a load.

Built detail

Steel thickness, load ratings and finish

Every bench and shelving unit we sell leaves the workshop with a spec sheet stapled to the frame. That sheet lists the steel gauge, weld type, paint finish and the tested load limit, so you can compare our gear against anything imported at half the price without guessing what is inside the tube. The frames are welded, not bolted, on all four corners, then powder-coated in a colour that hides grinding dust and weld spatter better than bare mill steel. If you need a size we do not list, we fabricate to measure at our South Brisbane workshop, usually within ten working days from sign-off on the drawing.

Custom sizes available. Send us a rough sketch and we will quote the fabrication.
2mm Steel bench top thickness
350 kg Load per shelf bay
125mm Castor diameter on cabinets
10 days Turnaround on custom builds
Fabrication standards

Welded corners, tested to failure

Our fabricators load-test one bench from every production run and record where the frame starts to deflect. That data feeds back into the design, which is why our current benches hold their shape better than the version we sold five years ago.

  • Four-corner welds, inspected and signed off
  • Deflection measured at 25, 50 and 75 percent of rating
  • Powder coat cured to resist weld spatter
  • Adjustable feet fitted as standard on every bench
480 Benches and racks fabricated last year
14 yrs Fabricating in Queensland
Workshop setup

Storage packages that scale with the shed

Prices cover fabrication, powder coating and delivery within Brisbane metro. Assembly on site is available for larger runs.

Single bay

Home workshop setup

$845 incl. GST

One bench and a short shelving run for a home garage or a small trade shed.

  • 1.8m steel-top bench with adjustable feet
  • Two-bay shelving unit, 900mm per bay
  • Set of six storage bins
  • Delivery inside Brisbane metro
Order the home setup
Full shop fit

Complete workshop fit-out

$5,760 incl. GST

A measured fit-out for larger workshops, including fabrication to the dimensions of your bay.

  • Three benches fabricated to your wall length
  • Shelving run sized to the full bay
  • Two rolling cabinets with divided drawers
  • Overhead steel racking for long stock
  • Floor layout drawing supplied before fabrication
  • Delivery, assembly and levelling on site
Book a fit-out visit
Ordering process

Measuring, fabricating, installing

Storage only works if it fits the space. Here is how we get there.

1

Site measure

We measure the wall, note the door swing and check the floor for slope before anything is drawn.

2

Layout plan

You get a simple top-down drawing showing where each bench, shelf and cabinet sits.

3

Fabrication quote

The quote lists steel gauge, finish and load rating, so the price is easy to compare.

4

Build and coat

Frames are welded, dressed and powder-coated at our South Brisbane workshop.

5

Delivery and install

We deliver assembled where access allows, bolt the units down and level every bench.

6

Handover and support

You receive the spec sheet, a care guide and a direct line if anything needs adjusting.

Recent builds

Workshops we have fitted out

A handful of jobs from the past year, photographed on site after installation.

Storage questions

Answers before you measure up

The questions we get most from workshops planning a new layout.

Send a photo of your wall with a tape measure in frame and we will suggest a layout.

Not always. Bays under 2m tall with light loads can stand free on adjustable feet, but anything taller or carrying heavy parts should be bolted down for safety.

The 2mm steel top on our 2.4m bench handles 600kg spread evenly. Concentrated weight like a vice or a press is fine, but keep it over a leg or a cross member.

Yes. We powder coat to most standard colour codes, and there is a small surcharge for a custom tint. Lead time adds about four working days.

That is normal in older sheds. Our adjustable feet and a scribed end panel take up the difference, and we check it during the site measure.

Yes, on the trade and full fit-out packages. Our installers bolt the units down, level every bench and take away the packaging.
Book a measure

Send us the space you are working with

Give us the wall length, ceiling height and what you need to store, and we will come back with a layout and a quote.

+61 7 3168 4259
actionchoiceflow@gmail.com
275 Grey Street, South Brisbane QLD 4101