Pro-Grade Cordless Power Tools
Actionchoiceflow stocks 18-volt and 54-volt cordless platforms built for Australian tradies. Every drill, impact driver and circular saw on this page has been bench-tested by our Brisbane team before it earns a spot on the shelf, so you know it will survive a full day on site.
One battery, every tool
Lock into a single platform and swap packs between the drill, grinder, saw and blower. No more mixing chargers in the ute.
Built for real sites, not showroom floors
We only carry cordless gear that has survived a hands-on test in our South Brisbane workshop. If it slips, stalls or eats batteries, it does not make the list.
18V brushless drill and driver combo
Two-speed gearbox, 65Nm of torque and a metal chuck that grips under load. Comes with two 4.0Ah packs and a carry case.
165mm cordless circular saw
Cuts 55mm at 90 degrees, so it handles 45mm framing and decking without bogging. The rafter hook keeps it out of the dust.
125mm angle grinder with paddle switch
Paddle switch that stops the disc in under two seconds, and a guard you can rotate without taking the tool apart.
What you actually get in the box
Actionchoiceflow bundles cordless tools the way you would build the kit yourself: real batteries, not the 1.5Ah throwaway that ships with the wallet-friendly version. Each combo includes a matching fast charger, a hard case with foam cutouts and a belt hook. We register the serial numbers in our system, so if a pack fails inside the warranty window you can walk in with the tool and walk out with a replacement. No courier loop, no waiting three weeks for a warehouse at the other end of the country to answer an email.
A tech tests every tool before it ships
Our workshop runs each cordless tool through a 40-minute cycle before it earns a place in the range. We drill 30 holes, drive 60 screws and run the battery to cutoff, then measure how hot the pack gets on the way down. Tools that overheat or slip under load go back to the supplier with our notes attached.
- Battery packs run to full discharge and timed on recharge
- Chucks and blades measured against factory spec
- Switch and clutch cycles logged for repeatability
- Every unit photographed for our internal fault log
Pick the package that fits your tray
Prices include GST and are set per kit, not per tool. Trade accounts get 30-day terms and free delivery inside a 25km radius of South Brisbane.
Starter twin kit
A drill and impact driver on the same battery, with the essentials to get on site this week.
- 18V brushless drill and impact driver
- Two 4.0Ah battery packs
- Single-port fast charger
- Hard carry case with foam insert
Carpenter five-piece
The kit we sell most to framing crews and decking builders who need to move between tools fast.
- Drill, impact driver and 165mm circular saw
- 125mm angle grinder with paddle switch
- Reciprocating saw body
- Three 4.0Ah packs and a dual-port charger
- Rolling tool bag with reinforced base
Site crew bundle
Enough cordless gear for a three-person crew, with shared charging and a locked storage case.
- Three of every core tool across the range
- Six 5.0Ah high-output packs
- Four-port workshop charging station
- Site-safe steel storage case
- Priority repair turnaround
- On-site induction for your crew
From first call to first cut
No mystery steps. Here is exactly how a cordless order moves through our South Brisbane branch.
Tell us the job
A quick call or a walk-in chat about what you are building, the materials and how often you use each tool.
Match the platform
We check the batteries you already own so any new tool fits the same charger and packs.
Test on the bench
Your chosen tool gets a run in our workshop before it is packed, and you get the test sheet.
Register the warranty
Serial numbers go into our system so claims stay local and you skip the courier back-and-forth.
Deliver or collect
Free delivery inside 25km of the store, or pick it up the same day you place the order.
After-sales support
Brushes, chucks and switches stay on the shelf for the life of the tool. Bring it in and we will sort it.
Cordless gear earning its keep
Photos from our bench and from jobs our customers have sent through over the last twelve months.
The 18V drill after a 30-hole framing test on hardwood.
Driving 14g batten screws into treated pine without cam-out.
Cutting 90mm decking at a shallow angle on site.
Paddle switch grinder set up with a new 125mm cut-off disc.
The four-pack charging rotation we recommend for crew use.
The five-piece kit packed for a Monday morning departure.
Before you buy cordless gear
Things tradies ask us most often at the counter in South Brisbane.
Tell us what the job needs
Send through the details and one of our team will come back with a kit recommendation, pricing and lead times.